Huth End Finishing Swager
All Huth tooling is machined to specific tolerances from solid steel. After it is machined, it is gas-carburized and oil quenched to a minimum hardness of 58 Rockwell “C” scale. We do not use cast iron for any of our tooling. All Huth tooling is available from shelf stock. However, Huth will manufacture custom tooling to your specification for sizes not listed in this schedule.
Contact Us for Details >
Clamp Collets (All Models After Jan '85)
No.
Imperial Size
1775
3/4″ EMT
1709
1″ EMT
1710
1″
1718
11 ⁄8 “
1714
11 ⁄4 “
1756
15 ⁄16 “
1738
13 ⁄8 “
1712
11 ⁄2 “
1758
15 ⁄8 “
1734
13 ⁄4 “
1778
17 ⁄8 “
1720
2″
1720DF
2″ Double Flare (Use with Part #518)
1728
21 ⁄8 “
1725
21 ⁄4 “
1723
23 ⁄8 “
1750
21 ⁄2 “
1729
23 ⁄4 “*
1731
27 ⁄8 “*
1730
3″*
* Requires 892 Collet Holder
For Clamp Collets Prior To 1985 See Replacement Parts – Vintage
No.
Metric Size
1740
40mm
1742
42mm
1745
45mm
1700
48mm
1705
50mm
1728
54mm* * *
1755
55mm
1760
60mm
* * * 21 ⁄8 ” = 54mm
Huth Swage Dies
No.
Imperial Size
110
1″
118
11 ⁄8 “
114
11 ⁄4 “
138
13 ⁄8 “
112
11 ⁄2 “
158
15 ⁄8 “
134
13 ⁄4 “
178
17 ⁄8 “
120
2″
128
21 ⁄8 “
125
21 ⁄4 “
123
23 ⁄8 “
150
21 ⁄2 “
129
23 ⁄4 “
130
3″
No.
Metric Size
140
40mm
142
42mm
145
45mm
148
48mm
149
50mm
128
54mm* * *
155
55mm
160
60mm
* * * 21 ⁄8 “=54mm
Huth Reducing Dies
* Reducing Dies Require Clamp Collet 890, 891, or 892.
No.
Imperial Size*
775
For 3/4″ EMT .799 OD
779
For 1″ EMT 1.024 OD
780
2″ to 13 ⁄4 “
781
21 ⁄4 ” to 2″
782
21 ⁄2 ” to 21 ⁄4 “
783
3″ to 21 ⁄2 “
784
2″ to 17 ⁄8 “
785
13 ⁄4 ” to 15 ⁄8 “
786
15 ⁄8 ” to 11 ⁄2 “
787
11 ⁄2 ” to 13 ⁄8 “
788
13 ⁄8 ” to 11 ⁄4 “
789
11 ⁄4 ” to 11 ⁄ 8 “
790
3″ to 23 ⁄4 “
No.
Metric Size*
760
(50mm to 45mm OD)
761
(55mm to 50mm OD)
762
(65mm to 60mm OD)
Ball Joint Tools - Female
No.
Size
555
13 ⁄4 ” , 17 ⁄8 “, 2” (Female)
556
21 ⁄4 ” to 21 ⁄2 ” (Female)
564
23 ⁄4 ” to 3″ (Female)
Ball Joint Tools - Male
No.
Size
550
13 ⁄4 ” (Male)
551
17 ⁄8 ” (Male)
552
2″ (Male)
553
21 ⁄4 ” (Male)
554
21 ⁄2 ” (Male)
557
13 ⁄4 ” to 21 ⁄2 ” (Domer)
558
25 ⁄8 ” to 23 ⁄4 ” (Domer)
Flaring/Flanging Tools
Flaring/Flanging Tools Specs
No.
Size
518
Flare Tool – 2″ Double Flare and 11 ⁄2 ” Flat Flare*
519
Flare Tool – 13 ⁄4 ” and 15 ⁄8 ” Double Flat Flare*
853
Pipe Flanger 11 ⁄2 ” to 3″ – (Replaces Pipe Flangers 848, 849, 850, 851)
* NOT SHOWN
Swager Tools
No.
832
Double End Cylinder Stop- Used to control cylinder stroke
Header Collector Tool
No.
Size
101
3″
102
31 ⁄2 “
